Binary
Dave posted a nice tut about it on the old forums.
| Mirage Source http://www.miragesource.net/forums/ |
|
| Better Method http://www.miragesource.net/forums/viewtopic.php?f=201&t=514 |
Page 1 of 1 |
| Author: | halla [ Thu Sep 14, 2006 7:37 pm ] |
| Post subject: | Better Method |
Ok im setting it where it reads variables to set the damage, monster so on fo the battle. Whats better... to have all the monsters in 1 ini file and it searches for the monster name and gets the data.. OR have each monster have its on ini file. about the first I was thinking that but is there a way to have it read the first category and then set that as a variable? the format is [name] name=value im talking about the [name] is it possible to set that to a variable? if so im not sure how... or is just making all their own ini file easier. I would just do that but it seems more sloppy... even though thats how ms and so on does it. THanks |
|
| Author: | funkynut [ Thu Sep 14, 2006 8:18 pm ] |
| Post subject: | |
speed wise, each monster own ini, since when searching inis it searches everything until it finds what its looking for, if each is in its own ini, then It can go directly to it |
|
| Author: | Obsidian [ Thu Sep 14, 2006 8:50 pm ] |
| Post subject: | |
Just out of curiousity why are you even using INIs? |
|
| Author: | halla [ Thu Sep 14, 2006 9:09 pm ] |
| Post subject: | |
Yeah I figured out to use the first method I could do say... [MONSTER1] Name= Monster then I could have it get the name that way. If it does slow it down then I will change it not hard to do so. Why am I using INIs? Im using it to store monsters info and stuff like that... prob player info too. Im doing that so so I wanted to have monster 1 and monster 2 randomly be in fights on a map I just pull their info from the INI file. And for player of course could just take all their info from the file. I know for players it could just all be in the game but say you save the game or whatever it saves to ini file so it can load it up when you continue the game. Do you hvae a better method to do this? Im open to all suggestions. |
|
| Author: | Van [ Thu Sep 14, 2006 9:41 pm ] |
| Post subject: | |
Binary
Dave posted a nice tut about it on the old forums. |
|
| Author: | halla [ Thu Sep 14, 2006 9:43 pm ] |
| Post subject: | |
Van wrote: Binary
Dave posted a nice tut about it on the old forums. this isnt online though... unless that doesnt amtter (I dont know) |
|
| Author: | Spodi [ Thu Sep 14, 2006 10:01 pm ] |
| Post subject: | |
It would be best if you had a variable-sized array with pointers to the index of the array that is used for the NPC, then just load the NPCs as they are needed. |
|
| Author: | halla [ Thu Sep 14, 2006 10:08 pm ] |
| Post subject: | |
it does only load npcs when they are needed. when the battle is opened it loads up the npc that is set for it. what do you mean set an array... 1 value for each npc and then have it load the info based on what array is selected? like Monster(2) would load the second monster? |
|
| Author: | Spodi [ Thu Sep 14, 2006 10:32 pm ] |
| Post subject: | |
I am talking about a variable length array, and what position NPCs are in the array is when they are loaded: Monster(1) = first loaded monster Monster(2) = second etc... Sizing your array to fit all the monsters but just not setting them is just a waste of RAM. 
|
|
| Author: | halla [ Thu Sep 14, 2006 10:49 pm ] |
| Post subject: | |
my way doesnt waste ram I have variables for everythin on the battle screen and it just sets everything based on what those variables are... and they just read from the monsters info... I dont see how that wastes ram |
|
| Author: | Spodi [ Fri Sep 15, 2006 12:01 am ] |
| Post subject: | |
Well you are grabbing information from a file constantly, which will reduce speed quickly since file I/O, especially with Get/SetPrivateProfileString, is very slow. |
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|